Teyleten Robot TMC2209 V2.0 Stepper Motor Driver StepStick 2.5A UART Ultra Silent for Nano SKR V1.3/1.4 Ender 3 Control Board 3D Printer Parts Replace A4988 5pcs
Thumbnail 1Thumbnail 2Thumbnail 3Thumbnail 4Thumbnail 5Thumbnail 6Thumbnail 7Thumbnail 8Thumbnail 9

Teyleten Robot TMC2209 V2.0 Stepper Motor Driver StepStick 2.5A UART Ultra Silent for Nano SKR V1.3/1.4 Ender 3 Control Board 3D Printer Parts Replace A4988 5pcs

4.1/5
Product ID: 359797194
Secure Transaction
12 interest-free installments with tabby

Details

  • Brand
    Teyleten Robot
  • Voltage
    5.5 Volts
  • Item Weight
    0.03 Kilograms
  • Manufacturer
    Teyleten Robot
  • UPC
    755454774471
⚡2.5A Power
🔊Ultra Silent
🌡️Efficient Cooling

Description

🚀 Elevate Your 3D Printing Game!

  • POWERFUL PERFORMANCE - Harness the strength of 2.5A for superior motor control.
  • VERSATILE VOLTAGE RANGE - Compatible with input voltages from 5.5V to 28V for diverse applications.
  • WHISPER QUIET OPERATION - Experience the tranquility of ultra-silent 3D printing.
  • ADVANCED HEAT MANAGEMENT - Equipped with a large heat sink for optimal thermal performance.
  • SMART SENSORLESS FEEDBACK - Enjoy enhanced precision with innovative sensorless feedback technology.

The Teyleten Robot TMC2209 V2.0 Stepper Motor Driver is a cutting-edge solution for 3D printing enthusiasts, featuring the new original German TMC2209-TA chip for exceptional silent operation, a robust 2.5A output, and a wide input voltage range of 5.5V to 28V. Its large heat sink ensures efficient heat dissipation, while the sensorless feedback function enhances precision, making it a perfect upgrade for your Nano SKR V1.3/1.4 or Ender 3 control board.

Reviews

4.1

All from verified purchases

G**S

Works great for my 3D Printer

Upgraded my Prusa MK 2.5S with these drivers, they are really the game changer. My printer is now super quiet and runs smoothly. I used for all XYZE motors with a driver breakout from Custom Circuit Co. in Sweden. Runs well with 24 VDC.

S**R

ATTENTION ANYCUBIC MEGA X USERS - THIS REVIEW IS FOR YOU

The media could not be loaded. I bought these drivers as a swap in for my ANYCUBIC Mega X's stock stepper drivers because the stock drivers are super loud.Like many 3D printing hobbyist, I YouTubed how to install them but these general videos will not help you with these specific drivers beyond a certain point.Key points that will remain the same for those videos and these drivers:1) You have to disconnect your stepper motors from the board, pull the plastic input housing off the pins and flip it 180 degrees. Reinsert this housing on the pins. Then flip your cables over and plug them in like that.2) When adjusting VREF with a multimeter on each driver's potentiometer, each one should be between 1.1V and 1.2V. I did 1.1V for every stepper except the extruder (E0). For that one, I did 1.2V based off of a wealth of research.Okay, that's where the similarities between these drivers and the instructional videos end.The product description says UART or Direct Step are both driver setting options. This is not the case if you have an ANYCUBIC Trigorilla board in your printer because the ability to adjust steps manually does not exist on those boards and is defaulted to 16 steps.So what does that mean?It means if you install them as is in UART mode, your axises will be a hot mess express. My Y axis kept going all the way forward or backwards and just grinding there. My X axis wouldn't move at all. Only my Z axis worked correctly.I scoured forums, videos, and Facebook groups for help and finally found someone who was patient enough to help me figure this out.Basically, to turn UART off and set the driver to direct step mode (which is the mode you need for these printers that use Trigorilla boards) you need to bend 3 pins all the way sideways so they do not insert into the board. (please see attached photos for reference).If you look at one of these 2209 drivers straight on with the 3 copper circles being the top (yellow pins should be on the right), you're going to bend flat out to the side the 3rd, 4th, and 5th pins on the right side.This turns UART off and converts this into a direct step driver. Now you can carry on without the 5+ hours of troubleshooting and confusion that I endured.This process works fine with stock firmware and Knutwurst. I don't run Octoprint or Klipper, but I'd imagine it'd work for those too.Once I'd done this to all 5 stepper motors and turned the printer off and back on, the axises corrected themselves and now all home appropriately with no grinding.Happy Printing!

A**C

Good Stepper Drivers at a Great Price

I was a little hesitant to order these as they were pretty significantly cheaper than some of the more known brands and had no reviews, but decided to take a chance and I'm glad I did. As seen in the picture, the chip is a TMC2209, not a 2208 like I feared I might get for the price. The board is mostly unlabeled, but the pinout is in the pictures in the product listing and the enable pin is labeled. I currently have them running in standalone mode on a 3d printer (AnyCubic Chiron). I did adjust the Vref before using them as it was not at the value I needed out of the package. The heatsink is nice and large and they really quiet down the printer. I swapped them in for some A4988 drivers and I did have to reverse the motor direction in firmware, but I've also read you can just reverse the motor wire connection also. It is important to note that compared to an A4988, the enable pin needs to. E lined up in the same place, which makes it look like the drivers are reversed compared to the old ones. Unfortunately none of my other printers have removable stepper drivers, but I wouldn't hesitate to buy more of them if I ever blow a driver.

B**E

:(

The first 3 out 5 were junk, so I'm not even checking the other 2.1 - Had the little resistors and capacitors falling off out of the bag. (Poor durability)2 - Rewired everything 3 times based on the diagrams, and it would still kill my Arduino. (Bad internal circuitry)3 - Using the same wiring and dropping in #3, the issues with #2 didn't occur, but I couldn't get the step pin to work. Adjusted frequency, the current flow, etc. to no success on turning my stepper. (Bad internal circuitry)Got the 5 pack because I needed 3 good ones and anticipated at least 1 failure. Now I don't trust the other 2 even if they work, so I'm just going to use a different driver.

J**R

These work GREAT on my Anycubic Chiron...

I had to adjust the VREF for each. I put x, and both z's at 1v and then the y at 1.15 and the extruder at 1.2. runs smooth, quiet and cool to the touch. I am not running klipper, because there isnt a whole lot of advantage on this massive printer. The gains in speed are negated by the weight of the bed and gantry, and most other features you can get in marlin. So, I run standalone and Marlin 2.x

S**N

quiet!

It really quite surprising how much quieter a stepper motor will run with a good driver!!! Used in a custom project with ESP32 WROOM.

B**E

Real TMC2209, Nice Heat Sink, No Diag Pin for Sensorless Homing

This TMC2209 is genuine but lacks the pins for diag connection. This is used for sensorless homing on some printers, step recovery on others. It all works but you have to add the pin yourself. I didn't notice that immediately, and another reviewer notes that it's missing feature(s) without that.The beefy heatsink has precise grooves cut out for the pin headers. The adhesive provided for the heatsink is effective. The heatsink is appropriate length where it leaves the 3 hole communication header available to connection on either side. The heatsink is my favorite part, and it matches some sinks for TMC2208 previously installed on other axes in the machine I used them in.Adding a pin is a bit of a pain, the lister should mention in the product description that they limited that feature. It was the lowest price for this genuine part on Prime, so best value I guess.

D**D

Used on my MKS GEN L V3

Perfect for my MKS board to control steppers. None of my stepper motors were over heated or made any unusual noise .. Works my 3D printer (TEVO TORNADO) perfectly

Common Questions

Trustpilot

TrustScore 4.5 | 7,300+ reviews

Ali H.

Fast shipping and excellent packaging. The Leatherman tool feels very premium and sturdy.

1 day ago

Anita G.

Good experience, but the tracking updates could be better.

2 months ago

Shop Global, Save with Desertcart
Value for Money
Competitive prices on a vast range of products
Shop Globally
Serving over 300 million shoppers across more than 200 countries
Enhanced Protection
Trusted payment options loved by worldwide shoppers
Customer Assurance
Trusted payment options loved by worldwide shoppers.
Desertcart App
Shop on the go, anytime, anywhere.
SAR 126

Duties & taxes incl.

KSAstore
1
Free Returns

30 daysfor PRO membership users

15 dayswithout membership

Secure Transaction
12 interest-free installments with tabby

Trustpilot

TrustScore 4.5 | 7,300+ reviews

Vikram D.

The MOLLE sheath is of exceptional quality. Very happy with my purchase.

2 weeks ago

Sneha T.

Received my product in pristine condition. Great service overall.

1 month ago

Teyleten Robot Tmc2209 V2 0 Stepper Motor Driver Stepstick 2 | Desertcart KSA